Ultra-Low-Cost Rigid Boards for Toys, Chargers & Disposable Electronics
Primary SEO keywords: phenolic PCB, single-layer phenolic PCB, SRBP PCB, FR-1 PCB fabrication, low-cost rigid PCB, paper-phenolic circuit board, budget PCB manufacturer.
What Is a Phenolic PCB?
Phenolic PCBs—also labelled FR-1 (Tg ≈ 130 °C) or FR-2 (Tg ≈ 105 °C)—use paper-based core material impregnated with phenol-formaldehyde resin. No glass cloth is present, so the laminate can be punched in one stroke and costs ≈ 40 % of standard FR-4.
| Property | Typical Value* | Design Impact |
| Dielectric constant εr (1 MHz) | ~5.1 | Higher εr → slower signal velocity; fine for < 30 MHz |
| Loss tangent (1 MHz) | 0.03 | Acceptable for low-frequency analog & power |
| Glass-transition temp Tg | 100 – 105 °C (FR-2) | Safe for Sn-Pb wave solder; not for Pb-free reflow |
| Z-axis CTE (below Tg) | 75 – 95 ppm / °C | Use aspect ratio ≤ 6 : 1 to protect barrels |
| Thermal conductivity | 0.25 W/m·K | Limited heat spreading—size power traces generously |
Always verify values in the laminate datasheet selected for production.
Why Select Single-Layer Phenolic PCBs?
Lowest BOM cost
~60 % cheaper than FR-4—ideal for throw-away or highly price-sensitive gadgets.
Sufficient electrical insulation
CTI ≈ 150 V supports low-voltage consumer goods (≤ 250 V AC mains with proper creepage).
Outstanding punchability
Outline, slots and large holes made in one punch cycle—no routing cost.
Light weight
Paper core is ~15 % lighter than FR-4 of the same thickness.
Easy scoring & depanel
Clean V-cut or steel-rule die-cut edges save post-processing time.
HIGHPCB is one of the largest Rigid PCB manufacturing factories in China, click on the link to see more.
Limitations to remember
- Unsuitable for Pb-free reflow; stick to tin-lead wave or hand solder.
- Lower mechanical strength—avoid heavy transformers or press-fit connectors.
- UL 94 HB flame rating by default; specify V-0 grade if mandated.
Typical Use-Cases
- Battery-powered toys & novelty lights
- Wall or phone-charger primary boards (≤ 15 W)
- Low-cost radios & TV tuner modules
- IR remote controls, garage-door key fobs
- Disposable medical/diagnostic strips
Phenolic PCB Manufacturing Flow
| Step | Process Note | Key Control |
| CAM & tooling | Punch map, panel utilisation | Clearance ≥ 0.25 mm |
| Punch / Drill | Tungsten-carbide bits for holes < 1 mm; punch slots | Max 200 hits per bit |
| Copper pattern | Dry-film resist + alkaline etch | Min trace/gap 0.25 / 0.25 mm |
| Solder mask | Epoxy LPI or peelable blue | Opening ≥ 0.10 mm |
| Surface finish | OSP (cost) or Hot-Air (Sn-Pb) | Tin ≥ 8 µm to combat oxidation |
| Depanelisation | Steel-rule die-punch | Burr ≤ 0.05 mm |
| Electrical test | Flying-probe, HiPot 250 V | Isolation ≥ 10 MΩ |
Design Guidelines (Engineer’s Cheat-Sheet)
- Thickness: 1.2 mm or 1.6 mm (thinner boards may warp).
- Copper weight: 35 µm standard; upgrade to 50 µm for currents > 1 A.
- Pad design: Keep annular-ring ≥ 0.30 mm; use square pads to resist pull-out.
- Hole plating: Rare; if interconnects are needed, use wire jumpers or eyelets.
- Thermal reliefs: 4-spoke pattern, spoke ≥ 0.30 mm.
- Creepage / clearance: Meet IEC 60335-1—e.g., 2.5 mm for 250 V basic insulation.
Phenolic vs CEM-1 vs FR-4 (Single Layer)
| Metric | FR-4 | CEM-1 | Phenolic |
| Relative cost | 1.0 | 0.7 | 0.4 |
| Punchability | Moderate | Excellent | Excellent |
| Wave solder | Excellent | Good | Fair |
| Pb-free reflow | ✔ | Borderline | ✖ |
| Mechanical strength | High | Medium | Low |
| UL-94 flame class | V-0 | V-0 | HB / V-0 |
Support All Types of PCB Fabrication
Biggest PCB Manufacturers
Why Order Phenolic PCBs from HighPCB?
- Dedicated punch tooling for burr-free edges and ±0.10 mm dimensional accuracy.
- Process-controlled Sn-Pb wave solder profiling—no blistering or delam.
- Prototype in 3 days, mass production in 7–10 days.
- Complete service: stencil fabrication, SMT/through-hole assembly, 100 % ICT.
Need the absolute lowest PCB cost?
Get an instant phenolic PCB quotation from HighPCB now and compress your product budget without sacrificing essential reliability!
FAQ
Is a phenolic PCB safe for mains voltage products?
Yes, if creepage distances follow IEC/UL guidelines and a V-0 grade laminate is specified.
Can I mount SMD parts on phenolic boards?
Yes—use Sn-Pb wave or selective-solder; avoid long thermal dwell and heavy BGAs.
What panel size can HighPCB supply for phenolic?
Up to 350 × 450 mm on hydraulic punch presses with ±0.15 mm tolerance.
Are phenolic boards RoHS compliant?
All phenolic (SRBP) laminates we stock are RoHS 2 and REACH compliant; bromine-free versions available on request.
